Read on to learn the basics of laser vs. Learn more. Find printing solutions that integrate with your specific workflows, help increase productivity, and generally make daily work simpler. Learn more The Brother Workhorse Series scanners are designed for mid to large-sized workgroups or high-volume and batch scanning applications.
|Published (Last):||4 July 2017|
|PDF File Size:||4.48 Mb|
|ePub File Size:||14.9 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. See also: Operating Manual. Operation Manual. Table of Contents. Page 2: Important Safety Instructions Always unplug the machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual.
This sewing machine is not intended for use by young children or infirm persons without supervision. For Australia and New Zealand only Page 4 Appendix to inspect and adjust the machine yourself. If the problem is still there, consult your local authorized dealer. For additional product information and updates, visit our web site at www. The contents of this manual and specifications of this product are subject to change without notice. Page 6 ————————————————————————————————————————————————————————— 5.
We have designed these accessories to help you be able to carry out most sewing tasks. Part Name Zipper foot 1 pc. Bobbin 3 pcs. Using other power sources may result in fire, electric shock, or damage to the machine. Checking the Needle The sewing needle must always be straight and sharp for smooth sewing. Page Changing The Presser Foot Hold the needle with your left hand, and then use a screwdriver to turn the needle clamp screw counterclockwise to remove the needle.
Lower the presser foot lever and fix the presser foot onto the shank. If the presser foot is in the correct place, the bar should snap in. If the needle is in the down position when you turn the pattern selection dial, the needle, presser foot or fabric may be damaged.
Stitch Width Dial The numbers marked on the dial represent the stitch width. Using other bobbins may cause damage to the machine.
If you use bobbins from other models, the machine will not work properly. Page 19 While holding the end of the thread, gently press the foot controller to wind the thread around the bobbin a few times. Then stop the machine.
Trim the excess thread above the bobbin. Press the foot controller to start. When the bobbin seems full and begins spinning slowly, take your foot off the foot controller. If bobbins from other models are used, the machine will not operate correctly. Put the bobbin in, feed the end of the thread through the slit, and then pull the thread to cut it. Page Upper Threading counterclockwise so that the mark on the handwheel points directly up. Be sure to turn the handwheel so that the mark on the wheel points up before threading the sewing machine.
Check the table on page 26 for the appropriate needle and thread combinations. Pull on the upper thread to draw up the lower thread. The flat side of the needle should face toward the back and the rounded side should face toward you. Keep your hands away from moving parts. Raise the presser foot and turn the fabric to its new direction using the needle as a pivot.
Lower the presser foot and start sewing in the new direction. Each is explained below. Set the pattern selection dial to the Elastic Stitch. The Overlock Stitches are also useful for sewing stretch materials while the Arrowhead Stitch is ideal for sewing the edge of a blanket.
Page Adjusting Buttonholes Cut an opening in the middle of the buttonhole with the seam ripper tool. Be careful not to cut through any stitches. The seam ripper may slip and you may be injured. Loosen the tension of the upper thread so that the lower thread lies on the underside of the material. Sew a single row or many rows of straight stitches.
Baste the cut design to the fabric. Carefully sew around the edge of the design with a zigzag stitch. These materials are difficult to feed when sewing.
The walking foot prevents these materials from crumpling, slipping or sticking between the presser foot and the material. If the screw is loose, the needle may hit the presser foot and you may be injured. Sew while moving the fabric slowly. If the main power switch is on when you change the light bulb, you may get an electric shock.
Page 47 Using a coin, remove the two screws. Lift up the needle plate as shown in the illustration, and then slide the needle plate to the left to remove it. If the problem is still there, contact your retailer or the nearest authorized service center.
Symptom Possible cause The machine is not plugged in. The main power switch is turned off. Turn on the main power switch. The sewing The bobbin-winder shaft is pushed machine does Page 49 Symptom Possible cause The area around the hole in the nee- dle plate is scratched.
The area around the hole in the presser foot is scratched. The upper thread breaks. The bobbin case is scratched, or has a burr on it. You have not used a bobbin that has been designed for this machine. You have not used the right combi- nation of fabric, thread and needle. Stitches are The needle is bent or blunt. You have not inserted the needle properly.
Show all Xc Bm Xl Print page 1 Print document 52 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
Brother XL 2600i Sewing Machine User Manual
Brother XL2600i FREE Instruction Manuals
Brother XL-2600 Operation Manual